Trade-focused materials and design support

Sign in or create an account

The Largest Selection of Architectural & Design Surfacing Materials

  • Home
  • Catalog
  • All brandsLab DesignsInterlamDuchateauATI Decorative SurfacesAkupanel ProEzobordEcoDomoDani LeatherTransOnyxTexturglasNovelio
  • Popular
  • Showroom
  • Acoustical PanelsArchitectural PanelsLaminatesVeneersSpecialty ProductsExterior PanelsWallcovering
  • Cart
  • Wishlist
0
  1. Home>
  2. Articles>
  3. How To Install Stratto Peel And Stick Leather Veneer

The Largest Selection of Architectural & Design Surfacing Materials

Help & Support

  • 1020 NW 6th Street, Suite H Deerfield Beach, FL 33442
  • 954-429-3883
  • support@roosintl.com
FacebookInstagramLinkedIn

Account

  • Sign in
  • Create account
  • Cart
  • Wishlist
  • Catalog

Featured materials

  • Sunburst
  • So Impressed
  • Red Rust
  • Raven

Explore

  • Showroom
  • Projects
  • Articles
  • About us
  • Contact
  • Order samples
  • In-stock materials
  • Line Card
  • Site map

© 2026 Roos International. All rights reserved.

Privacy Policy
All articles
Laminates and Veneers

How to Install Stratto Peel-and-Stick Recycled Leather Veneer

By Roos International · October 29, 2026 · 2 min read

Open shelving with recycled leather veneer back panels behind vases and books

How to apply EcoDomo Stratto peel-and-stick recycled leather veneer to walls, cabinetry, and furniture: surface prep, temperature, rolling, and cure time.

Stratto RLV is EcoDomo's recycled leather veneer with a factory-applied peel-and-stick adhesive (3M 9505 transfer tape). It goes on walls, cabinetry, and furniture. This guide follows EcoDomo's Stratto installation instructions.

Before you start

  • Install only on finished surfaces. Do not apply Stratto to bare sheetrock, raw plywood, or MDF.
  • Let the veneer and the surface sit at room temperature for at least 24 hours. Do not install below 50°F (10°C).

Tools and materials

  • Utility knife and a straight edge
  • Primer, roller, and 120-grit sandpaper (for walls)
  • Acetone-based cleaner and lint-free cloths (for cabinetry and furniture)
  • J-roller with a curved handle. Firm roller pressure is what bonds the adhesive; fingers or a cloth are not enough
  • A small needle for air bubbles; 3M Primer 94 for low-energy surfaces such as powder-coated metal or HDPE

Prepare the surface

Walls: clean the wall, apply one coat of primer to porous walls such as drywall or plaster, let it dry, then lightly sand with 120-grit and wipe clean.

Pre-finished cabinetry and furniture: lightly sand with 120-grit to cut the gloss, then wipe with an acetone-based cleaner. Avoid silicone-based cleaners.

Apply the veneer

  1. Measure the area and cut the veneer slightly oversized with a knife and straight edge.
  2. Peel the backing from one corner, working in sections rather than removing it all at once.
  3. Line the veneer up with the top edge and press it down gradually as you peel.
  4. Go over the whole surface right away with the J-roller, using firm, even pressure.
  5. Trim the overhang with the knife and straight edge.
  6. Prick any air bubbles with the needle and press them flat.
  7. Re-roll any area that feels loose, then leave the surface alone for 24 to 48 hours while the adhesive cures.

Samples and help

Order Stratto samples from the product pages (see how sampling works) or see them at our Deerfield Beach showroom. Roos International is the Authorized Florida Distributor for EcoDomo and supplies projects across the US; full-material pricing is given by quote. Read more in The Peel & Stick Recycled Leather Veneer.

Questions about these materials?

Our team can send samples, specs, and pricing.

Contact us

More articles

See all articles
Specified Metals Basketweave EBP002 Silver installed in an elevator lobby with Industrial design styling.Laminates and Veneers

November 9, 2026 · 6 min read

Decorative Metal Wall Panels: Laminates, Textured Metals, and Backlit Feature Walls

Decorative metal wall panels can take several forms: metal-look decorative laminate, embossed aluminum surfaces, or illuminated graphic panels. This guide compares the visual…

Bathroom vanity cabinets in a pale whitewashed woodgrain laminate under a light stone-look top.Laminates and Veneers

November 2, 2026 · 7 min read

How to Specify Matching Laminate Cabinet Fronts and Edgebanding

Matching laminate cabinet edgebanding starts with a complete face-and-edge specification, not a color name alone. This guide explains how designers and fabricators can review…

Workplace island and cabinetry in Lab Designs SC422 Orange, a solid orange matte laminate.Laminates and Veneers

October 31, 2026 · 7 min read

Digital Printed Laminates for Commercial Interiors: Design Range and Specification Guide

Digital printed laminates for commercial interiors can serve two distinct roles: carrying custom graphics and branding, or bringing a specified decorative pattern to casework and…